Skip to main content
DrywallPlanner

Basement Drywall Calculator

A 30 x 24 ft basement with 8 ft walls and one door takes 27 sheets of 4x8 drywall on the walls, 843 sq ft. Buy 30 to cover 10% waste, or 20 sheets of 4x12. Boarding the 720 sq ft ceiling too makes it 55 sheets of 4x8.

Enter the basement size, doors and egress windows. It counts the sheets, mud, tape and screws, prices labor and your board, and flags the thermal barrier that foam walls need.

  • Walls, ceiling optional
  • Board type choice
  • Foam thermal barrier
  • Layout counted

Basement size

ft
ft
ft
Slab to joists
Not sure the ceiling needs it? See the basement ceiling drywall code.

Doors and egress windows

3 x 7 ft each
Enter the size below

Board

Board type
Sheet size

Insulation

Your price

$
4' x 8' 1/2 in mold and moisture resistant, from your store

Your estimate

843 sq ft of board
30sheets of drywall
1/2 in mold and moisture resistant

Board

Sheets304' x 8', 27 laid out + 3 spare
Walls843 sq ftopenings deducted

Finishing

Joint compound2 boxes121 lb, 61.7 lb boxes
Paper tape2 rolls320 ft, 250 ft rolls
Screws843about 4 lb, at least 1-1/8 in into wood

Cost range

BoardAdd your priceUnder Your price
Hang and finish labor$1,012 to $2,108$1.20 to $2.50 per sq ft of wall and ceiling area

Foam walls

Thermal barrierRequired2024 IRC R303.4, 1/2 in board qualifies

Sheets come from a sheet-by-sheet layout plus 10% spare, the same engine as the main calculator. Egress windows are deducted from the area but boarded over in the layout. Labor is this site's national planning range, not a quote. Foam on the walls must be covered by a thermal barrier such as 1/2 in gypsum board under 2024 IRC R303.4 (R316.4 in 2021 and earlier), unless the foam product is approved for exposed use.

This calculator lays drywall onto the walls of a rectangular basement sheet by sheet, cuts out the doors, deducts egress windows at the size you enter, and adds the ceiling if you board it. It then works out compound, tape and screws, a labor range, and the board cost at your own price per sheet.

Worked example: the default is a 30 x 24 ft basement with 8 ft walls, one door, mold resistant board and foam on the walls. That is 843 sq ft of wall and 30 sheets of 4x8 (27 in the layout plus 3 spare), or 20 sheets of 4x12, with 2 pails of compound, 2 rolls of tape and about 843 screws. Labor at this site's planning range comes to $1,012 to $2,108 before board. Board the 720 sq ft ceiling as well and the order grows to 55 sheets of 4x8.

Egress windows come in many sizes, and the code minimum describes the net clear opening of the open window, not the hole in the wall, so enter your rough opening.

A basement is the one room where drywall goes up against concrete that sits in the ground. The sheet count works like any other room, but three decisions matter more here: which board to use, how to let the wall dry, and whether the board is doing a second job as the thermal barrier over foam insulation. Whether the ceiling needs drywall by code is a separate question with its own rules, covered in our basement ceiling drywall code guide listed under related tools.

Best drywall for basement walls

The code does not ask for special board on a basement wall. Section R702.3.5 of the 2024 IRC says interior gypsum board must not be installed where it is directly exposed to the weather or to water, so standard board meets code on a wall that stays dry. The real question is how dry yours will stay.

Building Science Corporation's basement renovation report recommends gypsum board without paper facings below grade, and says moisture-sensitive materials such as wood, paper and fiberglass batts should not touch concrete or masonry. Paperless, glass mat faced board follows that advice most closely. Paper-faced mold and moisture resistant board is the common middle choice, and the calculator's default.

Type X is fire-rated board, and the IRC does not call for it on ordinary basement walls. Buy it where your plans or building department ask for it. It is also heavier: about 2.2 lb per sq ft against 1.6 lb for regular 1/2 in board, by USG's published weights, which you will feel on a basement stair.

No board fixes a wet wall. BSD-103 puts groundwater control first: gutters, grade sloping away from the house, drainage and damp-proofing outside the wall. Fix any leak before you frame.

What thickness drywall for basement walls?

For most basements, 1/2 in. Table R702.3.5 allows 1/2 in board on wall framing up to 24 in on center, hung in either direction, with screws no more than 16 in apart on studs at 16 in and 12 in apart on studs at 24 in. The foam rule sets a floor too: over foam insulation the thermal barrier must be at least 1/2 in gypsum wallboard, so 3/8 in board does not qualify there.

Thicker board needs longer screws. The Gypsum Association's GA-216 gives a minimum of 1-1/8 in into wood framing for 1/2 in board and 1-1/4 in for 5/8 in, and the calculator shows the one for the board you pick. Ceiling thickness depends on joist spacing and texture, which the ceiling guide covers.

Vapor barrier behind basement drywall

Section R702.7 of the 2024 IRC requires a vapor retarder on the interior side of frame walls, with the class set by climate zone, but its first two exceptions are basement walls and the below-grade portion of any wall. The code does not require plastic sheeting behind basement drywall.

Building Science Corporation advises against it. BSD-103 explains that basement walls should dry toward the inside, and an interior plastic vapor barrier prevents that inward drying. It recommends foam insulation against the concrete instead, unfaced and semi-permeable: up to 2 in of unfaced extruded polystyrene or 4 in of unfaced expanded polystyrene meets its permeability targets. A frame wall in front of the foam can take unfaced fiberglass, with no vapor barrier. The same logic rules out vinyl wall coverings and impermeable paints on the finished wall.

Leave a gap at the slab

Hold the bottom edge of the board off the concrete. The wall detail in Building Science Corporation's renovation report shows 1/2 in gypsum board held up from the floor 1/2 in minimum, with a capillary break at the base of the frame wall. Paper-faced gypsum is a moisture-sensitive material, and a sheet sitting on a slab that gets damp, or wet from a small leak, draws that water up into the wall. Baseboard covers the gap.

Foam insulation needs a thermal barrier

Section R303.4 of the 2024 IRC (R316.4 in the 2021 and earlier editions) says foam plastic must be separated from the interior of the building by an approved thermal barrier, such as 1/2 in gypsum wallboard, unless R303.5 allows otherwise. Every board in the calculator meets that, and it means foam walls need board even in a part of the basement you leave unfinished.

Building Science Corporation puts it plainly: extruded polystyrene is flammable and must be protected by a 15 minute thermal barrier such as 1/2 in gypsum board. Its report shows two ways to do it: wood furring strips attached through the foam with power-driven nails or screws, with the board screwed to the furring, or a 2x3 or 2x4 frame wall built just inside the foam. Either way the screws go into wood rather than foam.

Alternatives to drywall in a basement

  • Wood structural panel: R303.4 accepts 23/32 in wood structural panel as a thermal barrier, so plywood of that thickness can cover foam on its own. Thinner paneling is not on the list unless it has passed the NFPA 275 fire tests the section names, so over foam it normally goes on top of gypsum board.
  • Foam approved for exposed use: R303.5 and R303.6 let some foam go without the barrier in certain uses or when the product has passed approved fire tests. Building Science Corporation notes that gypsum is needed when the rigid insulation is not rated for exposed application, so check the product listing before you leave it bare.

What the estimate counts

  • Sheets: a layout of each wall and the ceiling with offcuts reused, doors cut out at 3 x 7 ft, plus 10% spare.
  • Finishing: 0.14 lb of compound and 0.37 ft of tape per sq ft of board hung, in 61.7 lb pails and 250 ft rolls, and 1 screw per sq ft of wall and 1.25 per sq ft of ceiling as a buying allowance.
  • Cost: board at the price you enter, and labor at this site's national planning range of $1.20 to $2.50 per sq ft of wall and ceiling area. The labor pages scale it by state wages.

This page explains the model 2024 International Residential Code. Your state or city may adopt another edition or amend it. Check with your building department before you finish a basement.

Frequently asked questions

How many sheets of drywall do I need for a basement?

For a 30 x 24 ft basement with 8 ft walls and one door, about 30 sheets of 4x8 for the walls, 3 of them spare, or 20 sheets of 4x12. Boarding the ceiling too takes it to about 55 sheets of 4x8. Enter your own size above for your count.

How much does it cost to drywall a basement?

Labor for the walls of a 30 x 24 ft basement, 843 sq ft of board, comes to $1,012 to $2,108 at this site's planning range of $1.20 to $2.50 per sq ft. Add 30 sheets at your store's price, plus compound, tape and screws. Local wages move the labor figure up or down.

Can I use regular drywall in a basement?

Yes, on a wall that stays dry. The 2024 IRC rules out interior gypsum board where it is directly exposed to weather or water, and a dry basement wall is neither. Building Science Corporation recommends board without paper facings below grade, so mold resistant or paperless board is the safer buy.

Should basement drywall touch the concrete floor?

No. Building Science Corporation's basement wall detail holds the board at least 1/2 in off the slab, so it cannot wick up moisture from the concrete. The baseboard hides the gap.

Can drywall go directly over foam board on a basement wall?

It goes over the foam, but not fastened to it. Screw the board to furring strips fastened through the foam into the wall, or to a frame wall built in front of it. Over foam, the board is also the code thermal barrier, so it must be at least 1/2 in gypsum.

Is plastic sheeting needed behind basement drywall?

No. Section R702.7 exempts basement walls from the interior vapor retarder rule, and BSD-103 warns that polyethylene on a basement wall stops it drying to the inside. Use unfaced, semi-permeable foam against the concrete instead.

Primary references

IRC R702 and R303.4 set the board, fastening, vapor retarder and foam thermal barrier rules, ESR-5254 shows a foam listing, and Building Science Corporation and NAIMA cover moisture and vapor control.