Skip to main content
DrywallPlanner

Drywall Repair Cost Calculator

Replacing one 2 x 2 ft section of wall, cut back to the studs, primed and repainted, takes 5 hours over 4 visits and $142 of pro labor at the national median of $28.33 an hour, with one 2 x 2 ft repair panel, less than 1 qt of compound and 20 screws to buy.

Pick the repair, its size and the finish. The calculator lists the materials, counts the hours and visits, and prices pro labor at the BLS median wage for your state.

  • Nail pops to ceilings
  • Materials list
  • BLS state wages
  • Editable hours

The repair

Repair type
ft
Edges on stud centers
ft
Where

Finish

Texture to match
sq ft
Corner to corner, so the patch does not show

Who does it

DIY or pro
$28.33 an hour, BLS May 2025 United States median, drywall installers

Labor hours

Every hour here is our planning assumption, not published data. Change any of them to match a quote or your own pace.

h
Assumed, hands-on across all coats
Assumed, one per coat; ready-mix dries between
h
Assumed, drop cloths, mixing, cleanup
h
Assumed, prime and paint

Your store prices

Optional. We do not fill in prices, so enter what your store charges and only those items are totaled.

$
Per small tub
$
Per 2 x 2 ft repair panel
$
Per strip
$
Per 250 ft roll
$
Per 1 lb box
$
Per qt
$
Per gal

Your estimate

4 visits, 5 h of work
$142labor at the United States median wage
materials not priced yet

Materials

Joint compound1 small tubless than 1 qt, setting-type for the first coat helps
Drywall repair panel1 panel2 x 2 ft, or an offcut of the same thickness
Wood backers4 stripsAlong the cut edges between framing
Paper joint tape1 roll250 ft rolls, 8 ft of joint
Drywall screws1 box1 lb boxes, 20 screws, 1-1/4 in
Primer1 qtSpot-prime 4 sq ft of patch
Paint1 gal96 sq ft, 2 coats

Labor

Repair work2 h1 section x 2 h
Paint touch-up1 h
Setup and cleanup2 h4 visits x 0.5 h
Median wage$28.33/hBLS May 2025, United States median, drywall installers
Labor at that wage$1425 h in all

This is labor at the median wage only. A contractor's bill also covers travel, insurance, overhead and profit, and many charge a minimum service call for a small repair, so ask for theirs before comparing.

Choose the repair: nail pops, a small hole under 6 in, a medium patch, a replaced section, a full sheet or a water-damaged ceiling. Add the count and size, the surface, any texture to match and whether you will repaint. The calculator lists what to buy, totals the hours and visits, and multiplies the hours by the BLS median wage for drywall installers in your state.

Example: one 2 x 2 ft section of wall, cut back to the studs, primed and repainted over 96 sq ft. That takes one 2 x 2 ft repair panel, 4 wood backers, one 250 ft roll of paper tape for 8 ft of joint, 20 screws, less than 1 qt of compound, 1 qt of primer and 1 gal of paint. With the default hours it is 5 hours over 4 visits, $142 at the national median of $28.33 an hour.

We do not fill in store prices. Type what your store charges for each item and the calculator totals only those, so the DIY figure is always your own.

A drywall repair costs little in materials and a lot in trips. A tub of compound and a patch fix a doorknob hole, but every coat has to dry before the next one goes on, so even a small repair means coming back two or three times. That is why the calculator counts hours and visits rather than square feet, and why the hours are yours to change.

What drives the cost of a drywall repair

Three things set the price: the size of the damage, which decides the method; the number of visits, which follows from the coats; and the finish, meaning texture and paint. Materials rarely dominate: 6 nail pops take 12 screws and less than 1 qt of compound, but with the default hours they still add up to 2.5 hours across 2 visits.

Drywall repair cost by type

Under 6 in, a self-adhesive patch spans the hole. Up to what fits between studs, a piece of board goes in on wood backers. Past that, the repair is cut back to the framing. Here is what each type puts on the list, and the hours we assume for it on a wall; ceilings start a little higher.

  • Nail pops: 2 screws each, one beside the pop and one in place of the old fastener, plus a small tub of compound. 0.25 hours per pop, 2 visits.
  • Small hole under 6 in: one self-adhesive mesh or metal-backed patch per hole and a small tub of compound. 0.5 hours per hole, 3 visits.
  • Medium patch, 6 to 14 in: a piece of board, two wood backers, 8 screws and paper tape around the edge. A 10 in patch fits in one 2 x 2 ft repair panel or an offcut of the same thickness. Once the patches would take 8 panels, a full sheet of board, the list switches to 4 x 8 sheets. 1 hour per patch.
  • Replaced section: board cut to fit between studs, backers top and bottom in each stud bay, screws at the wall rate of 1 per sq ft plus 4 per backer, and tape all round. 2 hours per section.
  • Full sheet: one 4 x 8 sheet, 32 screws and 24 ft of taped joint, about 3 qt of compound. 2.5 hours per sheet.

Compound comes from USG's published coverage for all purpose compound, about 10 gallons per 1,000 sq ft of board, applied to the length of joint the repair creates. Edges cut from the middle of a sheet have no taper, so they take more feathering than the tapered joints that coverage figure assumes. Treat the amount as a floor.

How pro labor is priced

Labor is the total hours times the median hourly wage for drywall and ceiling tile installers in your state, from the BLS May 2025 Occupational Employment and Wage Statistics. Nationally that median is $28.33. BLS publishes no installer estimate for West Virginia, so that state uses the taper median instead.

Total hours are the hands-on time per repair, plus texture and paint if you add them, plus setup and cleanup on every visit. None of those hours is published data. They are our planning assumptions, shown as fields you can edit, so replace them with a quote or your own pace.

A wage is not a bill. A contractor's price also covers travel, insurance, overhead and profit, and many charge a minimum service call for small repairs, so a couple of nail pops can cost the same as a larger patch. Ask what the minimum is before comparing quotes.

Ceiling repair cost and water damage

A ceiling takes more screws, 1.25 per sq ft against 1 on a wall, and slower overhead work, so its default hours run higher. For a water-damaged ceiling, enter the cut-out across and along the joists. A 4 x 6 ft cut-out takes one 4 x 8 sheet, 20 ft of tape, 6 wood backers and 54 screws, plus stain-blocking primer. With a popcorn match that is 6 hours, or $170 at the national median.

  • Fix the leak first. EPA advises drying water-damaged materials within 24 to 48 hours; dried in that window, mold usually does not grow.
  • EPA says porous materials such as ceiling tiles may have to be thrown away if they become moldy, and that a moldy area under about 10 sq ft is usually a job you can clean up yourself. For larger areas it points to its remediation guide, and it recommends an experienced professional for mold hidden behind drywall.
  • Match the thickness of the board you cut out, and seal any remaining stain with a stain-blocking primer before paint.

Texture and paint: what makes a patch disappear

A patch that is flat can still show through a different texture or sheen. For orange peel or knockdown on a small patch the list calls for an aerosol, whose coverage varies by can. Larger areas use USG ready-mixed spray texture at 300 to 700 sq ft per 3.5 gal carton. Popcorn patch aerosols cover up to 4 sq ft per can (Homax), and bagged popcorn covers 256 to 320 sq ft per 32 lb bag (USG).

Paint the whole wall or ceiling, corner to corner, rather than only the patch. The calculator spot-primes the repair at 250 sq ft per gallon, the low end of Behr's drywall primer range, then puts 2 coats over the area you enter at 350 sq ft per gallon, the low end of Sherwin-Williams' 350 to 400.

Repairs in a house built before 1978

EPA's Renovation, Repair and Painting rule covers anyone paid to disturb painted surfaces in a home built before 1978. Minor repair is defined as 6 sq ft or less of painted surface per room indoors, but demolition of painted surface areas never counts as minor, so a contractor cutting out a painted section falls under the rule. Homeowners working on their own home are generally not covered, and EPA still recommends lead-safe practices.

Frequently asked questions

How much does it cost to fix a hole in drywall?

In materials, a self-adhesive patch and a small tub of compound per hole. Hired out, it is mostly time: two 4 in holes on a wall take 2.5 hours with the default hours, including setup on each of 3 visits, or $71 at the national median wage before the contractor's overhead or minimum charge.

How much does ceiling drywall repair cost?

It depends on the cut-out. A 4 x 6 ft water-damaged section with a popcorn match takes one 4 x 8 sheet, stain-blocking primer and 6 hours by the calculator's default hours, which is $170 of labor at the national median of $28.33 an hour. Choose your state to use its median wage instead.

Why do contractors charge a minimum for small drywall repairs?

Because the time is in the trips, not the patch. Compound has to dry between coats, so even a nail pop means coming back, with setup and cleanup each time. Many contractors set a minimum service call to cover that. Ask for it up front, and bundle several repairs into one visit.

How many visits does a drywall repair take?

One per coat, because ready-mixed compound has to dry before the next coat goes on. The calculator assumes 2 for nail pops and 3 for patches and replaced board (tape, fill and finish coats), plus one more when you add texture or paint. Change the visits field if your contractor works differently.

Does a contractor need lead certification to repair drywall in an older house?

Usually, if the home was built before 1978 and the work disturbs paint. EPA's RRP rule covers paid work on painted surfaces in those homes. Only jobs disturbing 6 sq ft or less of painted surface per room count as minor, and demolition of painted surfaces never does.

Primary references

BLS wages set the labor rate by state, USG, Homax, Behr and Sherwin-Williams give the material coverage, and EPA covers the lead paint and mold rules.