Home Improvement Calculators
Measure the room once. Sheets, compound, tape, screws, paint, insulation, flooring and tile all come from the same walls, openings and floor. Free, no sign-up.
- One room engine
- Free, no sign-up
- Embeddable
Start with the drywall calculator for a one-room shopping list: sheets, mud, tape and screws from three measurements. Use the layout planner when you need to know where each sheet and offcut goes, and the cost calculator when you are checking a contractor's quote.
The job pages begin from the size or rule that sets a job apart, such as 9 ft walls, a garage wall shared with the house or a 10x12 shed. The paint and insulation calculators take doors and windows out at the same 21 and 15 sq ft as the sheet calculator, and flooring and tile start from the same floor, so the numbers for one room agree.
Sheets, mud, tape and screws
Board count for one room, joint compound by finish level, tape from seam length, screws by spacing, bead per corner, order weight and a material and labor total.
By job
Sheets for 8, 9 and 10 ft walls, vaulted ceilings and stairwells, closet and patch costs, basements, the garage code check, 2 car garages, sheds and bathroom wet areas.
By room and house size
Sheet counts for 10x12, 12x12 and 20x20 rooms and for whole houses by square footage, each with its own layout.
Home improvement
Paint gallons, insulation batts, flooring boxes and tile count from the same room measurements.
Labor by state
Installed cost per sq ft and per sheet from BLS wages for installers and tapers, state by state.
Which calculator answers which question
- How many sheets, and how much mud, tape and screws for one room? Drywall Calculator, from length, width, height, doors and windows.
- Where does each sheet go, and how much is offcut? Drywall Layout Calculator, which draws every wall and ceiling sheet by sheet.
- Is a contractor quote in the right range? Drywall Installation Cost Calculator, which splits material and labor.
- Is the hourly rate in a quote normal for my state? Drywall Labor Cost by State, from BLS wages for installers and tapers.
- How many rolls of tape, counted from real seams rather than area? Drywall Tape Calculator.
- Will my truck carry the order, and in how many trips? Drywall Weight Calculator.
- What does a garage wall shared with the house need? Garage Drywall Code Requirements, which applies IRC Table R302.6.
One room, every trade
Because every tool reads the same room, one set of measurements carries through a whole remodel. Take a 12 x 12 ft bedroom with 8 ft walls, one door and one window. The walls are 384 sq ft before openings; less 21 sq ft for the door and 15 sq ft for the window, 348 sq ft are left to board, finish and paint, plus the 144 sq ft ceiling.
- Tape: 198 ft from a 4x8 layout or 164 ft from 4x12, one 250 ft roll either way.
- Primer for the new board: 492 sq ft at 250 sq ft per gallon, about 2 gallons.
- Paint, two coats at 350 sq ft per gallon: about 2 gallons for the walls and just under 1 for the ceiling.
- Flooring: 144 sq ft, 158.4 sq ft with 10% waste, 8 boxes of 20 sq ft, and 45 ft of baseboard after a 3 ft doorway.
The fixed figures behind the tools
Every default can be changed in the tool that uses it, but these are the starting values, and each tool page cites where its own figures come from.
- Doors come out at 21 sq ft (3 x 7 ft) and windows at 15 sq ft, in the drywall, paint and insulation tools alike.
- Joint tape for a quick estimate: 0.37 ft per sq ft of board, the USG rule of thumb; the tape calculator measures seams instead.
- Paint covers 350 sq ft per gallon per coat and primer 250, both editable to match the can.
- Flooring waste starts at 10% for a straight lay, 15% for diagonal and 20% for herringbone.
- Tile is counted per piece, with half the grout joint added around each tile.
Put a calculator on your website
Contractors, suppliers and home blogs can embed any of these tools for free. Each one resizes to fit and shows a small Drywall Planner credit inside the frame.
