Skip to main content
DrywallPlanner

How Much Drywall for a 10x12 Shed?

A 10 x 12 shed with 7 ft walls and a vaulted ceiling takes 17 sheets of 4x8 drywall, door and one window taken out. Buy 19 to cover 10% waste.

Drywall for a 10 x 12 ft shed with 7 ft walls: sheets for the walls, a flat ceiling or a vaulted one with both gables, plus the insulation to put in first.

  • 10 x 12 ft
  • Gable ends included
  • Flat or vaulted
  • Layout diagrams

Shed size

ft
Gable end, door wall
ft
Side walls
ft
Floor to top plate

Ceiling & roof

Ceiling
in 12
Gable rise 2.5 ft

Door & windows

ft
ft
3 x 5 ft, side walls

Board

Sheet size

Your estimate

10 x 12 ft shed, vaulted
17sheets of 4' x 8'
from a layout of every surface

Area

Walls, less door and windows267.0 sq ft
Both gable ends25.0 sq ft
Roof slopes134.2 sq ft

To finish it

Joint compound76 lb
Drywall screws460

Both gable triangles are cut from one panel the width of the shed and as tall as the gable, so they show as one surface. Add a spare sheet for a small job like this.

Opening67810 ft
Door wall10 ft x 7 ft, vertical, 3 pieces
Window9101112 ft
Side wall12 ft x 7 ft, vertical, 3 pieces
1213810 ft
Back wall10 ft x 7 ft, vertical, 3 pieces
14151612 ft
Side wall12 ft x 7 ft, vertical, 3 pieces
1222312 ft
Ceiling slope12 ft x 5 ft 7 in, horizontal, 5 pieces, 3 butt joints
453312 ft
Ceiling slope12 ft x 5 ft 7 in, horizontal, 4 pieces, 2 butt joints
5171710 ft
Both gable ends10 ft x 2 ft 6 in, vertical, 3 pieces

The shed calculator lays 4x8 or 4x12 sheets onto every wall, both gable triangles and the ceiling you choose, cutting around the door and windows, then reports the sheets from that layout with the compound and screws to hang and finish them.

Worked example: the 10 x 12 preset, 7 ft walls, a 4 x 6.5 ft door, one window and a vaulted ceiling under a 6 in 12 roof, comes to 267 sq ft of wall, 25 sq ft of gable and 134 sq ft of roof slope. That is 17 sheets of 4x8, about 76 lb of joint compound and 460 screws.

4x8, 4x10 or 4x12 for a 10 x 12 shed

Vaulted ceiling with both gable ends, door and one window, laid out by the layout engine
BoardSheetsButt jointsTaped seamsOffcut wasteLabor, national range
4x817598 ft21.7%$511 to $1,065
4x1013888 ft18.0%$511 to $1,065
4x12 (fewest joints)11473 ft19.3%$511 to $1,065

With the 7 ft walls this page starts from, a 4x8 sheet stood upright is trimmed 1 ft and covers the wall with no seam across it. With a 4 x 6.5 ft door and one window, the walls take 11 sheets of 4x8. A flat ceiling at wall height brings it to 15; boarding the underside of a 6 in 12 roof and both gable ends for a vaulted ceiling makes it 17. In 4x12 the vaulted build is 11 sheets.

Flat ceiling or vaulted in a 10x12 shed?

Under 7 ft walls a flat ceiling feels low, and the vault is what buys the headroom: the 6 in 12 roof rises 2.5 ft over the 10 ft width, so the ridge sits about 9.5 ft above the floor before framing depth. The price is board: 134 sq ft of roof slope and 25 sq ft of gable in place of a 120 sq ft flat ceiling, 2 more sheets of 4x8.

Surface by surface: the vaulted 10x12 shed in 4x8

  • Door wall, 10 by 7 ft, with the door opening: hung vertically, 3 pieces cut from 3 sheets, no butt joints, 14 ft of taped seam.
  • Side wall, 12 by 7 ft, with the window: hung vertically, 3 pieces cut from 3 sheets, no butt joints, 14 ft of taped seam.
  • Back wall, 10 by 7 ft: hung vertically, 3 pieces cut from 3 sheets, no butt joints, 14 ft of taped seam.
  • Side wall, 12 by 7 ft: hung vertically, 3 pieces cut from 3 sheets, no butt joints, 14 ft of taped seam.
  • Ceiling slope, 12 by 5.6 ft: hung horizontally, 5 pieces cut from 3 sheets, 3 butt joints, 19 ft of taped seam.
  • Ceiling slope, 12 by 5.6 ft: hung horizontally, 4 pieces cut from 3 sheets, 2 butt joints, 18 ft of taped seam.
  • Both gable ends, 10 by 2.5 ft: hung vertically, 3 pieces cut from 2 sheets, no butt joints, 5 ft of taped seam.

On 7 ft walls the 4x8 layout stands the sheets up and trims each one 1 ft short, which leaves no horizontal seam at all. Each gable end is a 10 ft wide triangle rising 2.5 ft to the ridge; cut one out of a rectangle and the corner offcuts make the other, so both together are one 10 by 2.5 ft panel, 3 pieces of board in this layout.

In 4x12 board the same shed takes 11 sheets with 73 ft of taped seam, against 17 sheets and 98 ft in 4x8. 4x12 comes out ahead on both sheets (11) and butt joints (4).

Insulate the 10 x 12 shed first

Board over bare studs traps whatever moisture gets into the walls, so insulation goes in before the first sheet. Framed 16 in on center with 7 ft walls, this shed has 31 wall bays once the door is out, plus 3 gable batts and 18 rafter bays. Counted by bay, that is 4 bags of Johns Manville R-13 15 x 93 in kraft batts for the walls and gables and 2 bags of R-19 for the roof.

A small order you can haul yourself

The vaulted layout is 17 sheets of 4x8. By USG's weights a 4x8 sheet of 1/2 in regular board is 51 lb and lightweight board 40 lb, so the load is about 870 lb, or 680 lb in lightweight. Here 4x12 is the rare case that wins on joints as well as sheets, 11 sheets with 4 butt joints against 5 butt joints in 4x8, but 12 ft board needs a truck or delivery, and it has to turn through a 4 ft shed door.

Hired out, the 426 sq ft of a vaulted 10 x 12 comes to about $511 to $1,065 in labor at the national range of $1.20 to $2.50 per sq ft. On a job this small, ask whether the quote has a minimum charge.

The 10 x 12 shed in 4x12, piece by piece

  • Door wall, 10 by 7 ft, with the door opening: hung horizontally, 3 pieces cut from 2 sheets, no butt joints, 6 ft of taped seam.
  • Side wall, 12 by 7 ft, with the window: hung horizontally, 4 pieces cut from 3 sheets, 1 butt joint, 12 ft of taped seam.
  • Back wall, 10 by 7 ft: hung horizontally, 3 pieces cut from 3 sheets, 1 butt joint, 13 ft of taped seam.
  • Side wall, 12 by 7 ft: hung horizontally, 3 pieces cut from 3 sheets, 1 butt joint, 15 ft of taped seam.
  • Ceiling slope, 12 by 5.6 ft: hung horizontally, 2 pieces cut from 2 sheets, no butt joints, 12 ft of taped seam.
  • Ceiling slope, 12 by 5.6 ft: hung horizontally, 2 pieces cut from 2 sheets, no butt joints, 12 ft of taped seam.
  • Both gable ends, 10 by 2.5 ft: hung horizontally, 2 pieces cut from 2 sheets, 1 butt joint, 3 ft of taped seam.

Long board suits this footprint because the 12 ft side walls and the 12 ft roof slopes are each exactly one sheet long.

Frequently asked questions

How much drywall for a 10x12 shed?

About 11 sheets of 4x8 for the walls with 7 ft walls and the door deducted, 15 with a flat ceiling, or 17 for a vaulted ceiling with both gable ends. Add a spare sheet for a job this small.

How much insulation do I need before drywalling a 10x12 shed?

With 7 ft walls framed 16 in on center and the roof insulated: 4 bags of R-13 15 x 93 in batts for the walls and gables and 2 bags of R-19 for the rafters, counted bay by bay.

Can I drywall a 10x12 shed with 4x12 sheets?

Yes, and it gives the fewest joints here: 11 sheets of 4x12 with 4 butt joints, against 17 of 4x8 with 5 butt joints. The catch is getting 12 ft sheets home and through the door.

Primary references

USG's weight table gives the load of board, USG's installation guide covers the hanging, and Johns Manville's fact sheet gives the batts per bag.